In preparation for an upgrade to ONTAP 9.6P8 software, you have uploaded the ONTAP image 96P8_q_nodar_image.tgz onto your local web server with address 192.168.10.10.
Which is correct command syntax to download this image to the cluster image repository?
Which two commands confirm whether an aggregate is WAFL inconsistent? (Choose two.)
Which two statements are correct when describing L1 and L2 Watch Dog Resets (WDR)? (Choose two.)
You have replaced the cluster backend switches on a 4-node NetApp ONTAP cluster with new switches. After the replacement, you realize that the system shows errors for the old switches that were removed:

You also notice that system switch ethernet show shows four switches, the two old switches and the two new switches.
What action will resolve the issue?
In which two sections of AutoSupport can you find information to analyze the following panic? (Choose two.)
Panic_Message: PCI Error NMI from device(s):ErrSrcID(CorrSrc(0xf00),UCorrSrc(0x18)), RPT(0,3,0):Qlogic FC 16G adapter in slot 1 on Controller
During a health check you observe that NetApp ONTAP software is reporting CRC errors on a network port from a node in the cluster.
Which component do you reseat?
When you plan an ONTAP upgrade, which NetApp tool generates a detailed upgrade plan?
On an AFF A700 system, a SAS stack is connected to SAS ports 2a and 2b. The system has an additional 4-port SAS card in slot 9.
How should the cabling the corrected for best practices?
Which command can you use to confirm successful completion of an ONTAP upgrade?
You have identified that the file named quarterly_25.docx is inconsistent.
Which nodeshell command reports whether there are Snapshot copies available?
You are upgrading your 6-node NetApp ONTAP cluster from ONTAP 9.9.1 to 9.16.1. As part of the ONTAP software upgrade process, you need to update the cluster switches. After you update the first switch, you receive the following AutoSupport message:
Exhibit — AutoSupport Alert
vifmgr: callhome.clus.net.degraded:alert:
Call home for CLUSTER NETWORK DEGRADED:
Large MTU Packet Loss - Ping failures detected
between Node1_clus1 (169.254.2.94) on Node1
and Node2_clus2 (169.254.248.67) on Node2.
All cluster ports and interfaces are in an up/up status.
What is causing this error?
After a panic, the customer asks you to explain the error “watchdog timeout.”
Which explanation would be appropriate?
Users are reporting slowness when accessing certain volumes with extremely high-performance requirements via NFSv3 on a four-node switched NetApp ONTAP cluster. Other volumes on the same cluster are behaving normally. Investigation reveals that there is a high amount of throughput recorded for the cluster LIFs.
What action enables you to determine which volumes are affected?
A node has panicked with a PCI/NMI error. Giveback has not been performed.
Which two commands should you run to collect the logs to determine the cause? (Choose two.)
What are two valid commands that can be used to trigger an AutoSupport? (Choose two.)
Which statement best describes the functionality of RAID Error Propagation (REP)?
While reviewing a fresh install of a new NetApp ONTAP HA pair, the Field Support engineer notices that the controllers do not report the same system storage configuration.
The first controller reports the following:
System Storage Configuration: Multi-Path HA
The second controller reports the following:
System Storage Configuration: Single-Path HA
There are no EMS errors, and there are no alerts on the system or on NetApp ONTAP System Manager.
What is the next step in troubleshooting this issue?
While setting up a replication between two clusters, an administrator receives the following error message:
Failed to create cluster peering with 'Error: RPC to peer address 192.168.31.10 failed'.
What is the cause of this issue?
Your 2-node switchless cluster controllers are being upgraded. All cables are correctly connected. After the first controller is replaced, one of the cluster LIFs is not coming online.
You examine the port by running the following command:
Exhibit — Network Port Configuration
netapp::* > network port show -port e4a|e4e
-node netapp-02 -instance
Node: netapp-02
Port IPspace Broadcast Domain Link MTU Speed(Mbps) Health
e4a Cluster Cluster down 9000 1000/- -
e4e Cluster Cluster up 9000 auto/40000 healthy
Which parameter must you change to bring e4a up?
NAHSE |