Black Friday Madness- 75% Discount Offer - Ends in 0d 00h 00m 00s - Coupon code: fifty75ct

301a BIG-IP LTM Specialist: Architect, Setup, and Deploy (301a) Questions and Answers

Questions 4

An LTM Specialist needs to add a pool that will load balance MYSOL services. It has four members, each with differing hardware platforms. All pool members are already assigned to another pool for load balancing FTP traffic.

Which load balancing method is most effective when the LTM Specialist sets up the pool?

Options:

A.

Observed (node)

B.

Predictive member)

C.

Round Robin

D.

Least Connections (node)

Buy Now
Questions 5

An LTM Administrator receives an email from the NOC stating that the switch connected to the backend server was shut down for maintenance. The BIG-IP device handles only UDP traffic. The BIG-IP device did not fail over to a DR location when no pool members were available.

When the LTM Administrator checks the pool, it confirms that the monitor is still marking UP the pool member.

A tcpdump of the traffic shows the following output:

A list of the monitor configuration shows the following:

Which two modifications to the LTM configuration will mark this pool member down, when the switch is down? (Choose two.)

Options:

A.

increase the timeout to three times the interval

B.

add a reverse string to the game monitor

C.

enable reverse and wait for the next connection

D.

also assign a gatewayjcmp monitor to the pool

E.

enable manuai-resume on the same monitor

Buy Now
Questions 6

A Web Server Administrator uses a manual process to display a page when the service is down.

Which feature on the LTM device should be used to automate the service down page? :

Options:

A.

Enable Request Queueing

B.

Action on Service Down

C.

Redirect Rewrite

D.

Fallback Host

Buy Now
Questions 7

A VCMP guest has the following characteristics:

• Resources allocated for CPU memory, network interfaces, and disk space

• Virtual disk created

• The guest is NOT running

The guest is NOT running in which state is the VCMP guest

Options:

A.

Offline

B.

Deployed

C.

Provisioned

D.

Configured

Buy Now
Questions 8

Connection mirroring performance impact

An LTM Specialist plans to enable connection mirroring for a virtual server in an HA environment. What must be considered before implementing the configuration change? (Choose one answer.)

Options:

A.

The add-on licence required for this feature

B.

Decreased number of possible concurrent connections

C.

Impact on system performance that might be noticeable

D.

Creating the required separate interface for connection mirroring

Buy Now
Questions 9

An LTM Specialist to configure a backend server to be disabled it takes longer than 30 seconds to respond to a request.

Which values should the LTM Specialist enter for interval and timeout?

Options:

A.

Interval 10, timeout 30

B.

Interval 10, timeout 31

C.

Interval 30, timeout 30

D.

Interval 30, timeout 91

The official recommendation is that timeout 3 times the interval value +1.

Buy Now
Questions 10

Refer to the following iRule:

What is a complete list of profiles that must be applied to the virtual server for this iRule?

Options:

A.

Fast L4, HTTP

B.

TCP, HTTP

C.

TCP, HTTP, Client SSL

D.

Fast L4 , HTTP, Stream

Buy Now
Questions 11

An LTM device configuration is as shown:

An LTM device configuration is as shown

What should be the two expected outcomes based on this configuration? (Choose two.)

Options:

A.

A client session that has been idle for 16 minutes will be sent to the same pool member

B.

A client session that has been idle for 20 minutes will be balanced to a new pool member

C.

A client session that has been idle for 14 minutes will be balanced to a new pool member

D.

A client session that has been idle for 48 minutes will be sent to the same pool members

E.

A client session that has been idle for 12 minutes will be sent to the same pool member

Buy Now
Questions 12

in which Application Visibility and Reporting (AVR) profile must the SMTP profile be defined to configure notifications via email?

Options:

A.

App analytics profile

B.

virtual server profile

C.

custom analytics profile

D.

default analytics profile

Buy Now
Questions 13

What should an LTM Specialist configure on an LTM device to send AVR notification emails?

Options:

A.

Email notification to be sent via iControl from the LTM device

B.

Syslog on the LTM device to send to an SMTP server

C.

Custom SNMP traps on the LTM device for AVR notifications

D.

Email notification to be sent via SMTP from the LTM device

Buy Now
Questions 14

An application is being load balanced through the LTM device using the configuration displayed below.

The network has been re-engineered to NAT all client connection. As a result, all client connections are hitting the same pool member.

Which changes should the LTM Specialist make in order to restore load balancing functionality wile maintaining session persistence?

Options:

A.

Change the virtual server type to Standard, add an http profile, and change the persistence profile to Destination Address

B.

Leave the virtual server type set Performance (Layer 4) and change the persistence type to hash

C.

Change the virtual serer type to Forwarding (Layer 4) and leave the persistence type to hash source Address

D.

Change the virtual server to Standard add an http profile, and change the persistence profile to Cookie persistence

Buy Now
Questions 15

A virtual server is configured to handle https traffic. The clientssl profile is configured to use a 2048-bit RSA key. Due to security requirements, is the LTM Specialist needs to use a 4096-bit RSA key in the future.

What two effects will this change have on the BIG-IP device? (Choose two)

Options:

A.

Increase of CPU usage on the BIG-IP device

B.

Decrease to 20% of licensed TPS

C.

Decrease to 90% of licensed TPS

D.

Increased of concurrent connection on client-side

E.

Increase of TLS Renegotiation

Buy Now
Questions 16

The web application team requests help from the LTM Specialist to Improve the performance of their web sites that are load balanced by the BIG-IP LTM device with a Standard Virtual Server.

Which virtual server type will improve the performance of the web application servers?

Options:

A.

Performance (HTTP)

B.

Performance (Layer 4)

C.

Stateless

D.

Forwarding (IP)

Buy Now
Questions 17

FTP continuity using connection mirroring

An LTM Specialist administers an HA pair of LTM devices that load balance multiple applications. Users of a critical FTP service must receive minimal or no interruption during failover. Which action should the LTM Specialist take? (Choose one answer.)

Options:

A.

Using an internal VLAN, configure a mirroring IP address and enable connection mirroring for the persistence profile

B.

Configure a new VLAN, configure a mirroring IP address, and enable connection mirroring for the virtual server

C.

Configure a new VLAN, configure a mirroring IP address, and enable connection mirroring for all persistence profiles

D.

Using an internal VLAN, configure a mirroring IP address, and enable connection mirroring for the SNAT used by the virtual server

Buy Now
Questions 18

Block unwanted admin source by packet filter

An unwanted IP address tries to connect to the Configuration utility through a Self IP. An LTM Specialist needs to block the attempts based on the IP address without affecting other users. How should the LTM Specialist block the attempts? (Choose one answer.)

Options:

A.

Packet filter

B.

Device trust

C.

SSH IP allow list

D.

Port Lockdown

Buy Now
Questions 19

An LTM Specialist upgrades the switching infrastructure and the backend servers on the LAN segments.

The LTM Specialist notices a 20% memory usage increase on the BIG-IP device while handling the same number of concurrent connections.

A comparison of statistics pre-upgrade and post-upgrade shows a significant reduction on the following:

-RTT between the BIG-IP device and the backend servers

-Packet drops in the switch

Time to First Byte (TTFB)

The LTM Specialist is concerned with the scalability of the number of concurrent connections with the new memory usage.

Which setting should be changed to reduce the memory usage on the BIG-IP device?

Options:

A.

Reduce the proxy buffer high setting on the server-side TCP profile

B.

Increase the receive window of the client-side TCP profile

C.

Increase the proxy buffer high setting on the server-side TCP profile

D.

Reduce the idle of the client-side TCP profile

Explanation

After adjusting the architecture, the network quality becomes better. With the connection unchanged the memory usage increase by 20%. It means that the sending speed of the server is higher than the receiving speed of the client. F5 caches more content on the memory and causes the memory usage to….

Buy Now
Questions 20

An LTM Specialist is the administrator of an HA pair that contains two BIG-IP units and one floating traffic group (TG1). A new project requires the creation of 30 virtual servers. The Specialist decides to create a new floating traffic group (TG2) to handle this requirement. Objects for this project created by the BIG-IP Managers must appears in the correct traffic group.

Which configuration should the LTM Specialist use to meet the requirement?

Options:

A.

Move the BIG-IP Managers from TG1 to TG2

B.

Create a new partition and set the default traffic group to TG2

C.

Modify the default traffic group of the Common partition to TG2

D.

Restrict the Traffic Group Access of BIG-I Managers to TG2

Buy Now
Questions 21

Application sessions behind reverse proxy

An LTM Specialist is configuring a virtual server for a web application that stores sessions on the backend web server to authenticate the user. All incoming traffic comes from a proxy server, and the application uses the Least Connections load-balancing method. Which persistence method should the LTM Specialist use to ensure that each end user is directed to the same backend server with every request? (Choose one answer.)

Options:

A.

Destination Address Affinity

B.

Cookie

C.

SIP

D.

Source Address Affinity

Buy Now
Questions 22

Traffic to a pool of SFTP servers that share storage must be balanced by an LTM device.

What are the required profile and persistence settings for a standard virtual server?

Options:

A.

tcp, ctientsst, ftp serverssl persistence

B.

tcp, clientssl, serverssl persistence

C.

tcp, ftp - Source address persistence

D.

tcp - no persistence profile will be used

Buy Now
Questions 23

A new HTTP server has been deployed on an LTM device. The application running on the server must be monitored by the LTM device. The following is required:

A new HTTP server has been deployed on an LTM device. The application running on the server must be monitored by the LTM device. The following is required:

When the server is unavailable, it will send an HTTP status code of 200 in response to a request for the status html page.

When the server is available. I will send and HTTP status code of 201 in response to a request for the status html page.

When the 200 status code is received, the pool member should receive No new connections.

Which configuration change should be made to meet these requirements?

Options:

A.

set the Send String to GET/ status html and the Receive String to 200 and Receive Disable String to 201.

B.

set the Send String to GET Arian and the Receive String to 200 and Receive Disable String to 201.

C.

set the Send String to GET Arian and the Receive Disable String to 200 and Receive String to 201.

D.

set the Send String to Get /status html and the Receive Disable String to 200 and Receive String to 201.

Buy Now
Questions 24

Active/passive FTP single virtual server

An LTM device needs to load balance active and passive FTP traffic while using a single virtual server. Which virtual server type should the LTM Specialist configure? (Choose one answer.)

Options:

A.

Forwarding (Layer 2)

B.

Stateless

C.

Forwarding (IP)

D.

Standard

E.

DHCP Relay

Buy Now
Questions 25

HTTP reverse monitor with missing UP response

An HTTP monitor is assigned to a pool with the nondefault settings: Interval 7 seconds; Timeout 22 seconds; Reverse Yes; Send String `GET /status.html HTTP/1.1\r\nHost: test.brave-dumps.com\r\nConnection: Close`; Receive String `UP`. The server response begins `HTTP/1.1 200 OK` and includes Apache, Keep-Alive, and text/html headers, but no `UP`. What is the resulting pool status? (Choose one answer.)

Options:

A.

Unavailable (Enabled)

B.

Unknown (Disabled)

C.

Offline (Enabled)

D.

Available (Enabled)

Buy Now
Questions 26

An organization’s development team creates an application to put behind the BIG-IP LTM device. The application can be quite load intensive at first, and then evens out over time. The team’s load balancing method needs to select a pool after taking into account the pool member’s response over the time to avoid landing on a busy pool member.

Which of the following load balancing methods meets this requirement?

Options:

A.

Fastest (application)

B.

Predictive (member)

C.

Dynamic (node)

D.

Observed (member)

Buy Now
Questions 27

An application is sensitive to packet loss and unexpected session termination. A pair of LTM devices is configured in an Active/Standby high availability configuration. SNATS are NOT used and the virtual server contains a Universal Persistence profile.

which two actions must an LTM Specialist take to ensure the sessions are maintained between the client and server during an LTM device failover event while maintaining maximum uptime? (Choose two.)

Options:

A.

configure a serial failover cable for mirror traffic

B.

configure a OneConnect profile to mirror connections

C.

configure a VLAN and primary mirroring address for mirror traffic

D.

enable Mirroring for a virtual server and persistence profile

E.

enable Clone Pools for a virtual server and a persistence profile

Buy Now
Questions 28

Self IP HA-only port lockdown

An LTM Specialist is reconfiguring a device for failover HA. All IP address settings have been configured between the devices. The LTM Specialist needs to allow the proper services through the existing Self IPs. The Self IPs are not currently allowing any services. Which Port Lockdown setting must be configured to allow only HA services? (Choose one answer.)

Options:

A.

Allow Default

B.

Allow All

C.

Allow Custom Include Default

D.

Allow Custom

Buy Now
Questions 29

TWO LTM devices are in the same Device Group and configured for Ac live/Standby Failover. The LTM Specialist observes that the HA Active and Standby device constantly changes state. All network links use the default route domain A dedicated fiber ink is used for the HA connection with a latency of 250 ms but no packet loss.

What is causing the change in failover state to occur?

Options:

A.

The HA network is using the default routing domain.

B.

The HA network is using multicast IP.

C.

The HA network is not configured for mirroring.

D.

The HA network latency is too high.

Buy Now
Questions 30

A web server ' s default gateway is the network router. The LTM Specialist needs to introduce an LTM device to load balance to the web servers without changing the server ' s default gateway.

Which deployment method and settings should the LTM Specialist use to ensure correct traffic flow and that the web servers can obtain the actual con IP addresses?

Options:

A.

route deployment with Automap configured and X-Forwarded-For inserted in HTTP headers

B.

route deployment without SNAT configuration

C.

SNAT deployment with automap configured and X-Forwarded-For inserted in HTTP headers

D.

SNAT deployment with automap configured

Buy Now
Questions 31

An LTM Specialist needs to create an iRule that creates persistence records based on a JSESSIONID cookie. If a persistence record already exists, then the iRule must persist the client connection according to the existing record.

Which persistence profile enables the iRule to meet these requirements?

Options:

A.

Universal

B.

SSL

C.

Destination Address Affinity

D.

Cookie

E.

Source Address Affinity

Buy Now
Questions 32

A company plans to launch a huge marketing campaign and expects increase demand of their secure website. With the current virtual server setup, the LTM Specialist expects that the LTM device will reach its capacity limits. For the wen application to function properly. Cookies persistence is required. The LTM Specialist needs to reduce LTM device load without breaking the application.

Which two settings should the LTM Specialist modify to meet the requirement? (Choose two.)

Options:

A.

Remove HTTP compression profile

B.

Remove HTTP profile

C.

Remove web acceleration profile.

D.

Modify virtual Server type to performance (Layer 4)

E.

Remove ClientSSL profile

It is required that cookie persist must be used and http profile must be used, and SSL offloading must also be required. It must be in standard mode, excluding BD E.

Buy Now
Questions 33

An TLM Specialist needs to configure a virtual server to terminate SSL connection on the LTM device.

Cryptographic information must be re-authorized for SSL sessions that remain open for longer than 30 seconds.

Which settings should the LTM Specialist configure in the client SSL profile?

Options:

A.

set the Handshake Timeout to 30 seconds

B.

enable Require Peer SN1 Support

C.

set the Renegotiate Period to 30 seconds

D.

set the Renegotiate Max Record Delay to 30

Buy Now
Questions 34

HA group external trunk failure threshold

A design requires the LTM device to become HA Standby when one of the two physical interfaces on the External trunk is down. The External trunk is an interface on the External VLAN. Which TMOS command enables this behaviour? (Choose one answer.)

Options:

A.

tmsh create sys ha-group External trunks add { External }

B.

tmsh modify net vlan External failsafe enabled

C.

tmsh create sys ha-group External trunks add { External attribute percent-up-members 100 }

D.

tmsh create sys ha-group External trunks add { External threshold 2 weight 101 }

Buy Now
Questions 35

An application is making heavy use of a large, high-quality JPEG image file. An LTM Specialist needs to enhance page load times without increasing server load.

Which profile should be applied to the virtual server to perform this task?

Options:

A.

Response Adapt

B.

OneConnect

C.

FastHTTP

D.

Web Acceleration

Buy Now
Questions 36

SFTP TCP with no persistence

Traffic to a pool of SFTP servers that share storage must be balanced by an LTM device. What are the required profiles and persistence settings for a Standard virtual server? (Choose one answer.)

Options:

A.

TCP; no persistence profile is used

B.

TCP, FTP; Source Address persistence

C.

TCP, Client SSL, FTP; server-side persistence

D.

TCP, Client SSL, Server SSL; persistence

Buy Now
Questions 37

A web server is being overloaded with HTTPS traffic. To decrease the load on the server, the LTM Specialist and the Server. Administrator decide to perform SSL offloading on the LTM device. The configuration of the virtual server is as follows:

Which change must be made to the configuration to perform SSL offloading?

Options:

A.

Remove the clientssl and http profiles

B.

Remove the clients profile

C.

Remove the clientssl and serverssl profiles

D.

Remove the severssl profile

Buy Now
Questions 38

A LTM device needs to load balance active and passive FTP traffic while using only a single virtual server.

Which virtual server type should an LTM Specialist configure on the LTM device?

Options:

A.

Forwarding (Layer 2)

B.

Standard

C.

Stateless

D.

DHCP relay

E.

Forwarding (IP)

Buy Now
Questions 39

An LTM device receives a response string containing " error "

Which monitor type and parameter will mark the HTTP server as down?

Options:

A.

HTTP monitor, Receive String " error " , and set the Reverse option to Yes

B.

HTTP monitor and Receive String " error ' ' ... flag is up

C.

HTTP monitor. Receive String " down " , and set the Reverse option to Yes .... flag is

D.

HTTP monitor and Receive Disable String " error ' ' .... flag is disable

Buy Now
Questions 40

Four members in a server pool have similar hardware platforms. An LTM Specialist needs the load balancing method that can select the server with the fewest entries in the persistence table.

Which load balancing method should the LTM Specialist use?

Options:

A.

Observed

B.

Dynamic Ratio

C.

Least Sessions

D.

Leas Connections

Pay attention to the examination questions, the stem is to ask the session to keep the minimum entries in the table.

Buy Now
Questions 41

A pool with a default connection limit is configured to use Round Robin as the load balancing method. An LTM Specialist needs to ensure that the LTM device selects a server with the fewest number of connections when new clients connect. Another pool is using the same set of backend servers.

Which load balancing-method should the pool be changed to?

Options:

A.

Weighted Least Connections (node]

B.

Weighted Least Connections (member)

C.

Least Connections

D.

Least Connections

Buy Now
Questions 42

Refer to the exhibit.

The http monitor is applied to a pool. All members are enabled. One server responds as follows.

What is the resulting status of this poo! member?

Options:

A.

Offline (Disabled)

B.

Offline (Enabled)

C.

Unavailable (Disabled)

D.

Available (Enabled)

The first picture " Send String " and " Receive String " are not clear. Send String should be " GOOD " , the response packet does not contain this keyword. Receive Disable String is completely unclear. If the response packet contains the content of Receive Disable String at this time, it will be Available (Disabled), If the content of Receive Disable String is not included, then Offline (Enabled).

Buy Now
Questions 43

An LTM Specialist regularly provides analytics reports that show that traffic generated by different subnets within the organization. The LTM Specialist needs show the associate department names next the IP addresses in the reports.

Which step should the LTM Specialist take to meet this requirement?

Options:

A.

use an iRule to change the output of the report

B.

export the report and add the department names manually

C.

create VLANs for each subnet and set the name accordingly

D.

define active subnets and assign a name to certain subnets

Buy Now
Questions 44

AN LTM Specialist needs to determine the delay between an LTM device and the internal web server for a specific client.

Which two AVR reporting options should the LTM Specialist enable to measure the delay? (Choose two.)

Options:

A.

User agents

B.

Methods

C.

Response codes

D.

Server latency

E.

Client IP

The problem is to specify the server delay of the client

Buy Now
Questions 45

Exhibit.

The three VLANS shown provide connectivity to backend servers. The backend servers are being moved to unmanaged switches and require separate interfaces.

How should the F5 device interfaces be configured?

Options:

A.

Create a Trunk interface and combined interface 1.1.1.2 and 1.3.

B.

Create a Trunk interface and select VLAN„A, VLAN_B. and VLAN_C.

C.

Create VLAN named VLAN_A enter 100 under Tag and move interface 1.1 to tagged Create VLAN_B enter 200 and move interface 1.2 to tagged Create VLAN_C Center 300 and move interface 1.3 to tagged.

D.

Create VLAN_A move interface 1.1 to untagged. Create VLAN_B move interface 1.2 to untagged. Create VLAN_C move interface 1.3 to untagged.

Buy Now
Questions 46

Aggressive memory reaping and RAM Cache

An HA pair of LTM devices that load balance multiple HTTPS applications utilizes highly customized RAM Cache and compression profiles on each virtual server. The LTM Specialist observes log entries similar to: tmm tmm[7085] sweeper_update: aggressive mode activated (117504/138240 pages). No DoS attacks are occurring. No user problems have been reported. Which step should the LTM Specialist take to help mitigate the issue? (Choose one answer.)

Options:

A.

Change the Adaptive Reaping Low-water Mark

B.

Allocate less memory to the RAM Cache feature

C.

Change the Adaptive Reaping High-water Mark

D.

Use a OneConnect profile

Buy Now
Questions 47

A virtual server is using a TCP profile based on the top-wan-optimized profile for a streaming application Users report videos are loading slowly.

Which setting should be modified in the TCP profile to optimize the application?

Options:

A.

Disable Slow Start

B.

Disable Selective ACKs

C.

Disable Nagle ' s Algorithm

D.

Disable Reset on Timeout

Buy Now
Questions 48

An SSL application is being migrated to the LTM device. Both encrypted and unencrypted traffic are accepted by the server. The virtual server configuration is as follows:

Which LTM device profile should be used on the LTM device to reduce the CPU load on the current.

Options:

A.

Protocol

B.

serverssl

C.

clientsssl

D.

stream

Buy Now
Questions 49

set payload {CACHE :: payload}

}

Which two profiles should be used on the virtual server? (Choose two.)

Options:

A.

http-transparent

B.

http compression

C.

http

D.

webacceleration

E.

stream

Buy Now
Questions 50

An LTM Specialist needs to create a virtual server to pass TCP traffic to three pool members.

Which two virtual server types should be used to meet the requirements? (Choose two)

Options:

A.

Performance (Layer A)

B.

Standard

C.

Forwarding (IP)

D.

Stateless

E.

Forwarding (Layer 2)

Buy Now
Questions 51

Image object requests and OneConnect

An organization uses a BIG-IP LTM device to load balance a web-based application that produces dynamic content. Page requests are being load balanced correctly. However, image objects are not being distributed across the pool of available servers. Which profile should the LTM Specialist enable to ensure requests are load balanced across the pool? (Choose one answer.)

Options:

A.

Web Acceleration

B.

Cookie Persistence

C.

OneConnect

D.

Compression

Buy Now
Questions 52

Refer to the exhibit

Given the bigip conf extract shown where the servers only talk http on port 80, which node will receive the next user request?

Options:

A.

72.10.1.1

B.

10.1.1.1

C.

10.1.1.2 0

D.

10.1.1.3

Buy Now
Questions 53

vCMP host HD1.2 upgrade

An LTM Specialist is completing an upgrade of a vCMP host to BIG-IP version 14.1. The system hosts a vCMP guest. The following software volumes are installed on the vCMP host:

Volume

Product

Version

Build

Active

Status

HD1.1

BIG-IP

13.1.3.2

0.0.4

Yes

Complete

HD1.2

BIG-IP

14.1.0.0

0.0.4

No

Complete

What is the supported method to complete this task? (Choose one answer.)

Options:

A.

On the vCMP guest, select HD1.2 in System > Software Management > Boot Locations; choose Yes to install configuration; select Activate.

B.

On the vCMP host, set the vCMP guest to Configured in vCMP > Guest List; activate HD1.2 through System > Software Management > Boot Locations.

C.

On the vCMP host, select HD1.2 in System > Software Management > Boot Locations; choose Yes to install configuration; select Activate.

D.

On the vCMP host, set the vCMP guest to Deployed in vCMP > Guest List; activate HD1.2 through System > Software Management > Boot Locations.

Buy Now
Questions 54

Two LTM devices must be manually configured to restrict in the same Device Group.

What is the correct order of steps to meet this requirement?

Options:

A.

Configure VLAN, Configure-Sync IP, Configure Failover type, Establish Device Trust, Sync Device Trust, Create type, Establish Device Sync Device Trust, Create Device Group.

B.

Configure VLAN, Configure Self-IPs, Configure Config-Sync IP. Configure Failover type, Establish Device Trust, Sync Device Trust, Create Device Group.

C.

Configure Self-IPs, Configure VLAN, Configure Config-Sync IP. Configure Failover type, Establish Device Trust, Sync Device Trust, Create Device Group

D.

Configure VLAN, Configure Config-Sync IP. Configure Self-IPs. Configure Failover type. Establish Device Trust, Create Device Group

Buy Now
Questions 55

An LI M device is experiencing a high volume of traffic. The virtual server is struggling under the load. The problem appears to be on the server side connections. The virtual server is accepting connections . The virtual server is accepting connections on https and is configured with an SSL profile and http pool.

What should be added to increase the performance of the device?

Options:

A.

an HTTP Compression profile

B.

a One Connect profile

C.

smaller key to the SSL profile

D.

a SPDY profile

Buy Now
Questions 56

An LTM Specialist reports that an application si no longer reachable after it has been upgraded.

Nothing has been changed in the configuration on the LTM device.

The logs indicates that health monitors to all servers have failed as shown:

What should the LTM Specialist verify next?

Options:

A.

That the TCP hand shake with the servers is stall completed using tcpdump

B.

That the custom receive string for the HTTP monitor has changed with the upgrade

C.

That the can still ping the servers from te BIG_ IP device.

D.

That the firewall between the BIG-ip device and servers is still allowing HTTP

The log shows that tcp detection is normal, but http detection is abnormal. So we should pay attention to the detection problem of http level

Buy Now
Exam Code: 301a
Exam Name: BIG-IP LTM Specialist: Architect, Setup, and Deploy (301a)
Last Update: Nov 18, 2026
Questions: 189
301a pdf

301a PDF

$22.5  $89.99
301a Engine

301a Testing Engine

$26.25  $104.99
301a PDF + Engine

301a PDF + Testing Engine

$35  $139.99