CompTIA XK0-005 Dumps Questions Answers

The system has reached its maximum permitted throughput, therefore iowait is increasing. The output of iostat -x shows that the device sda has an average throughput of 44.01 MB/s, which is equal to the disk maximum throughput of 44 Mbps. The output also shows that the device sda has an average iowait of 99.99%, which means that the CPU is waiting for the disk to complete the I/O requests. This indicates that the disk is the bottleneck and the system is slow due to the high iowait. The other options are incorrect because they are not supported by the outputs. The system has not reached its maximum IOPS, as the device sda has an average IOPS of 563.50, which is lower than the disk maximum IOPS of 690. The system is not mostly idle, as the output of top shows that the CPU is 100% busy. The system does not have a partitioned disk, as the output of lsblk shows that the device sda has only one partition sda1. References: CompTIA Linux+ (XK0-005) Certification Study Guide, Chapter 17: Optimizing Linux Systems, pages 513-514.

The command iptables -t filter -A INPUT -p tcp --dport 4000:5000 -j ACCEPT will enforce the rule of allowing incoming traffic to ports in the range of 4000 to 5000 on a Linux server. The iptables command is a tool for managing firewall rules on Linux systems. The -t option specifies the table to operate on, in this case filter, which is the default table that contains the rules for filtering packets. The -A option appends a new rule to the end of a chain, in this case INPUT, which is the chain that processes the packets that are destined for the local system. The -p option specifies the protocol to match, in this case tcp, which is the transmission control protocol. The --dport option specifies the destination port or port range to match, in this case 4000:5000, which is the range of ports from 4000 to 5000. The -j option specifies the target to jump to if the rule matches, in this case ACCEPT, which is the target that allows the packet to pass through. The command iptables -t filter -A INPUT -p tcp --dport 4000:5000 -j ACCEPT will add a new rule to the end of the INPUT chain that will accept the incoming TCP packets that have a destination port between 4000 and 5000. This command will enforce the rule and allow the traffic to the specified ports. This is the correct command to use to accomplish the task. The other options are incorrect because they either use the wrong options (-f instead of -t or -D instead of -A) or do not exist (iptables filter -A INPUT -p tcp --dport 4000:5000 -D ACCEPT or iptables filter -S INPUT -p tcp --dport 4000:5000 -A ACCEPT). References: CompTIA Linux+ (XK0-005) Certification Study Guide, Chapter 18: Securing Linux Systems, page 543.

The command that would resolve the issue is chmod 600 .ssh/authorized_keys. This command will change the permissions of the .ssh/authorized_keys file to 600, which means that only the owner of the file can read and write it. This is necessary for SSH key authentication to work properly, as SSH will refuse to use a key file that is accessible by other users or groups for security reasons. The output of ls -l shows that currently the .ssh/authorized_keys file has permissions of 664, which means that both the owner and group can read and write it, and others can read it.

The other options are not correct commands for resolving the issue. The restorecon .ssh/authorized_keys command will restore the default SELinux security context for the .ssh/authorized_keys file, but this will not change its permissions or ownership. The ssh_keygen -t rsa -o .ssh/authorized_keys command is invalid because ssh_keygen is not a valid command (the correct command is ssh-keygen), and the -o option is used to specify a new output format for the key file, not the output file name. The chown root:root .ssh/authorized_keys command will change the owner and group of the .ssh/authorized_keys file to root, but this will not change its permissions or make it accessible by the user who wants to log in with SSH key authentication. References: How to Use Public Key Authentication with SSH; chmod(1) - Linux manual page